Every night.
The whole sky. Saved.
A hand-built all-sky camera. One cable, no cloud, no subscription.
Put it up once. It runs every night.
An all-sky camera should record the sky, not give you another thing to babysit. SkyVault is built to be mounted, focused from your phone, and left alone.
Plug and play
It arrives assembled, set up and tested. Plug in one cable, open the page on your phone, and it starts recording at dusk.
One cable (PoE)
Power over Ethernet carries power and data on a single network cable, up to 100 m. No outdoor outlet, no power brick, no flaky Wi-Fi link.
Works without Wi-Fi
No internet, no account, no subscription. Everything runs on the camera. At a dark site it makes its own Wi-Fi so your phone can still connect.
Built for weather
UV-resistant parts, a polycarbonate dome and stainless hardware. Every unit runs for days before it ships.
One cartridge. Standard parts. Built to be repaired.
Many all-sky cameras are sealed boxes. When something fails, the whole camera goes back. SkyVault is modular: everything lives on one cartridge, and every part on it can be swapped or upgraded.
One cartridge
Camera, computer, storage and focus motor ride on a single core that unscrews from the bottom of the housing. The dome never has to come off.
Real SSD storage
A 256 GB M.2 NVMe drive, not an SD card. Faster, far more reliable over years of nightly writes, and room for months of nights.
The best parts available
Raspberry Pi 5, Sony's 12.3 MP HQ sensor, Power over Ethernet and active cooling. No bargain-bin boards.
Standard, swappable parts
The Pi, camera, drive and cable are standard parts. If one ever fails, you replace that part, not the camera.
Mount it anywhere.
Every tier comes with a bracket that clamps the camera to any standard 1¼″ pipe: a mast, a fence rail, or a wall standoff.
Nothing gets drilled into the housing, so there are no holes to leak. The arm holds the camera off to the side, so the pole stays out of the picture.
- ✓Fits standard 1¼″ pipe, like an antenna mast or chain-link post
- ✓Stainless hardware included
- ✓Same weatherproof material as the housing
- ✓The pole stays out of the sky view
Three ways in.
HOUSING KIT
The housing. You add the Pi and camera.
- ✓4″ housing body + 4.3″ polycarbonate dome
- ✓All 3D-printed parts in UV-stable ASA
- ✓Dew heater + dew control electronics
- ✓IP67 RJ45 connector + stainless mesh vent
- ✓Wall bracket + all mounting hardware
YOU PROVIDE
- + Raspberry Pi
- + Camera module + lens
Fully refundable until it ships
CAMERA KIT
Everything but the Pi.
- ✓Everything in the Housing Kit
- ✓Motorized autofocus, run from your phone
- ✓Arducam IMX477 HQ camera (12.3 MP)
- ✓~180° fisheye lens + CS adapter
- ✓5V→12V boost converter for the heater
- ✓CSI ribbon + camera hardware
YOU PROVIDE
- + Raspberry Pi 5
- + PoE HAT + storage
Fully refundable until it ships
FULL UNIT
Ready to mount. Just plug it in.
- ✓Housing, camera, fisheye + motorized autofocus
- ✓Raspberry Pi 5 + active cooling
- ✓PoE + NVMe HAT, 256 GB storage
- ✓SHT45 dew-point sensing
- ✓Assembled, focused, soak-tested, sealed
- ✓1-year warranty + tech support
YOU PROVIDE
- + A PoE+ switch or injector
Fully refundable until it ships
Hand-built in the USA in small batches. Reserve with a small deposit, fully refundable until your order ships. Orders ship in about 2 weeks; we invoice the balance plus shipping when yours is ready.